How to remove a large nail from a log. Safety device for pulling out nails. How to remove a nail from a wall

14.06.2019 Warm floor

How to remove a nail

Sooner or later in construction, the need arises to remove a nail from one or another object. There may be plenty of reasons for this; it’s worth knowing how to do it correctly. It’s exactly how to remove a nail that we’ll talk about today.

Nail extraction technology

To extract nails today you can use the most different instruments, For example:

nail puller,
ticks,
pliers,
hammer with a forked nose, etc.

But despite the fact that there is a large number of tools, in order to pull out a nail, you will need ingenuity and the ability to use one or another tool. For successful work you need to expose the nail head. In some cases, when the nail is exposed, it can be straightened and knocked out from the back. This can be done using a hammer and another nail.

To make the nail easier to move, the protruding part can be lightly lubricated with water, soap or grease. This lubricant will allow you to quickly remove the nail. It will be especially effective when the nail is rusty. In some cases, when pulling out a nail, part of it may break. Then, using another nail, you need to hit its end, which is located in the material. This action will allow you to raise the cap. For this purpose, you can use a rod or chisel of suitable diameter.

It is not always possible to get close to the tip of the nail. In most cases, it is located in the thickness of the workpiece. For this reason, it is necessary to pull the nail only by the head. For this, a chisel or a screwdriver that has a rod passing through the entire handle is suitable. Such a screwdriver will not break when hit with a hammer. As a result, a kind of mini-nail puller made from a screwdriver will help you remove the nail by the head. This screwdriver should have a forked blade, which, when bent in relation to the rod, will allow you to quickly get the job done.

But the head of the nail is not always accessible. In some cases it is recessed into the workpiece. In such cases, a different technique is used to pull out the nail. Make a small indentation around the head using a chisel. The recess should be sufficient to allow the nail to be caught with pliers. If you still fail to catch on to the cap, then it is best to cut it off and remove the old nail to the opposite side. To do this, you need to knock out a nail, as described above.

Pliers are a handy tool!

One of the most convenient tools for removing nails - pliers. It is best to have medium to small sized pliers. To reduce the effort needed to remove nails, it is recommended to purchase pliers with a long handle and wide jaws.

If your pliers have small handles, it is not recommended to lengthen them using a tube. This may cause injury!

If you decide to pull out a long nail, then you cannot do without intercepting it. Intercepting with pliers will be required when the rod extends 1 centimeter. Use pliers to grab the nail at the base of the workpiece. In this case, effort will be required, since the rod is smooth. To simplify this process, place a board under the supporting surface of the pliers. This method will allow you to remove nails from boards.

When using this method, be careful, especially when you plan to reuse the nail. If you pull out a nail with an overhang and pull it exclusively in one direction, you run the risk of pulling out a rainbow-shaped nail. To straighten it, you will need to straighten it; as a rule, this process is quite painstaking and time-consuming. Moreover, it will be extremely difficult to align perfectly. To prevent excessive bending, move the nail in different directions as you pull it out.

To avoid damaging the surface of the workpiece when removing the nail with pliers or other improvised tools, it is wise to use a special backing. If the surface is varnished, then you can put leather or other soft material under the board.

Carpenter's hammer and wire cutters as an alternative to a nail puller!

Concerning carpenter's hammer, then this item can serve as an excellent service for removing nails. You just need a hammer that has a forked nose on the other side. When using it without backing, do not pull out a long nail. Therefore, extraction occurs according to the method described above.

This method is effective, however, it carries dangers. If the hammer has a wooden handle, then using it repeatedly as a nail puller can break it. For this reason, it is best to have a hammer with a steel or polyurethane handle on the farm.

Using pliers to pull out nails is much easier than using a hammer. Moreover, if the nail does not have a head, then such a hammer will become completely useless, since it will simply slide along the rod.

As for wire cutters, they are best used when there is no other suitable tool. The fact is that they are used only for stripping wires of insulation, etc. If they are constantly used to remove nails, the cutting elements will very quickly become dull or chipped. It is also possible to bite through the nail, especially if it is made of mild steel.

How to properly remove a nail from a board?

In some situations, you will need to use several tools at once. If the nail is hammered all the way into the board and sticks out on the other side of the board for its entire length, you will need to first remove the nail using a hammer in the opposite direction. To begin with, it is best to coat the nail with oil or grease to make the process easier. To prevent the nail shaft from becoming dull, you can place an aluminum or brass plate. When the nail is completely knocked out, the remaining part must be removed with pliers.

Although not in all cases you need to pull the nail out of the board. If it will no longer be used in any way, then the part with the protruding nail can simply be cut off with a hacksaw.

In another case, when the boards are already rotten and the nails are still in good condition, do not rush to throw them away. You can remove the nails using any of the above methods.

If in front of you is a large wooden structure that is knocked down with a large number of nails, then you will have to apply force. To begin, give this structure a few blows with a sledgehammer or hammer. This is necessary so that gaps form between the knocked down parts. Then you can insert an ax or nail puller into them. This barbaric method can be used to restructure a large piece of wood and, accordingly, remove nails.

Here are, perhaps, the most common methods that will help you, if necessary, remove a nail from a wall, a piece of wood, and more. Now, if you don't have a nail puller that is specifically designed for this job, the tips above will help you get the job done. Remember, power is not the key in all cases. Most often, accuracy is valued, because with haste and great effort, you can bend a nail or tear off the head. Do not forget about safety measures: take care of your eyes and other parts of the body, because when pulling out nails there is a risk of injury.

See the guide to removing a rusty nail:

http://kakpravilnosdelat.ru

As a rule, the problem of pulling out nails occurs when carpentry work. For example, the simplest situation is when the nail head is above the surface, but unfortunately the nails that need to be pulled out are not always found in this form. In most cases, problems can arise with removing old nails whose heads are either recessed or torn off.

How to remove a nail from a board?

In cases where the nail is well recessed or without a head at all, you will need a well-sharpened chisel or, in extreme cases, a screwdriver in combination with a hammer. But this process can be completed with traditional pliers or wire cutters in such a situation, with the help of which, by easy swinging and scrolling, we pull it by the cap.
Much more difficult when peeling off carpeting from the floor, which, as a rule, is nailed with dozens, and in some cases even hundreds of small nails. Or when replacing a picket fence on a dilapidated fence. But you can cope with a similar task, since today you can find specialized tools on sale, with the help of which you can special effort, and most importantly, remove nails effectively. The nail puller for small nails is designed in such a way that not only an adult, but even a child can use it. If necessary, you can also adjust the step. The surface to be dismantled is picked up and lifted with a nail puller. And thus we pull out all the nails one after another.
It's another matter if you need to pull out an old nail, since with a greater degree of probability you can say that its head will break off. In this case, we act depending on the situation. For example, if you still have the opportunity to get to the bottom of the nail, then you need to knock it out as far as possible with a hammer, after which we pull it out completely with pliers. In cases with a nailed board, you can try using a pry bar or your hands to lift it so that it comes off the nail.
There is another option that can be used to deal with a “decapitated” nail. We make a notch with side cutters, and finish the work with end cutters.
In some cases, nails have to be removed from a surface that can be very easily damaged. To exclude such a scenario, you can place a durable material, on which we rely.
If you plan to pull out large nails with a nail puller, then it will be very difficult to do this in one step. In addition, as you remove the nail, you will need to place wooden blocks under the nail puller. In this case we will be able to create reliable support. In the same way, you can pull out large nails using pliers or wire cutters.

See also:

Nails are removed from the material using pliers, a nail puller, pliers, etc. At the same time, “extracting” nails from boards, shoes, etc. requires no less ingenuity and skill than hammering them. But in all cases, in order to use pliers or other listed tools, you have to lift (expose) the nail head.

When the end of the nail is bent, they straighten it and try to knock the nail out from the back. To make the nail come out of the material more easily when hitting its tip, the protruding part is lubricated with grease, soap, and water. Lubrication is especially necessary when the “tail” of the nail is heavily rusted. Note that when straightened, the “tail” often breaks off. Then, with the toe of a hammer or another nail, you have to act on the end of the “fragment” located in the material in order to lift the head of the latter. (Chisels, breakers, metal rods suitable size are also suitable for this purpose.)

But if you cannot reach the tip of the nail, since it is located in the thickness of the part, you can only lift the nail by the head. This is done using a chisel or a screwdriver with a rod passing through the entire handle (this one will not break!), as well as a hammer.

A special mini-nail puller made from a screwdriver with a forked blade, which is slightly bent in relation to the rod, will greatly facilitate the removal of the smallest nails.

There are times when it is not possible to pick up the cap with a screwdriver or a chisel. Then you will have to resort to using a chisel and make a depression around the head, which will help to tightly grasp the cap with the jaws of the pliers. If for some reason this option does not work, cut off the inaccessible head with a chisel, and use a suitable nail (or mandrel) to knock out the old nail from opposite side details.

So, we learned how to get to the head of a hammered nail and prepare (raise) it for gripping the nail with a specialized nail tool. Pliers are most convenient for removing clogged nails of small and medium size. The wider the jaws of the pliers (size “K” in the figure) and the longer their handles, the less force will be required to “lift” the wood rod. However, artificial lengthening of the handles using metal tubes unacceptable from a safety point of view, since the usual result of such rationalization is injury.

“Dragging” a nail with pliers is most convenient at first, when the sponges pick up the head. But now the rod protrudes from the wood by 5-10 mm and it becomes impossible to further pull the nail without changing the grip. Therefore, now you should use your sponges to grab the nail shaft below the head. But the rod is smooth and slippery. And in order to reliably hook the rod with the edges of the jaws, significant force is required. It would be nice to continue to pull out the nail and use the head again. This is possible if the supporting surface for the outer roundness of the jaws is increased by placing planks, plates, etc. under the pliers. By the way, a similar technique is used at subsequent stages of pulling out a nail, including using tools of a different design (nail pullers, wire cutters).

Here's another trick that will help you when pulling out nails. When a nail is removed stepwise (in several grips) from the wood, tilting the pliers in the same direction, the shape of the removed nail will resemble an arc, and without straightening such a nail cannot be hammered into the board again. However, the work of straightening the nail will be minimized if you use pliers in one plane, but tilt them in different directions when removing the nail. By the way, additional wooden or plastic supports placed under the outer roundness of the pliers jaws will perfectly protect the surface of the part itself from damage.

A carpenter's hammer with a forked nose is also useful for removing nails. And here the method of stepwise pulling out nails outlined above is quite acceptable. Is it true, wooden handle The hammer is not able to withstand such loads for long and usually soon breaks near the head. If this happens, and there are still a lot of hammered nails left, weld it to the hammer metal pipe suitable diameter. Now the claw hammer handle will not break.

But it’s still easier to use pliers than a hammer. The latter, due to its “frozen” dimensions, often turns out to be either too bulky or too miniature to grip the desired nail. And in the absence of a head on the nail, such a hammer can only slide along the rod.

Nails are pulled out with pliers only when there are no other tools. Please note that wire cutters are mainly used for stripping wires of insulation and cutting wires made of non-ferrous metals. That's why cutting edges The wire cutters will certainly become dull, or even chipped, if they are used to clamp steel nails. Moreover, while holding a nail with a diameter of 1-1.5 mm, you cannot squeeze the handles of the pliers too much, so as not to bite the nail.

When pulling out nails, the hammer head sometimes turns out to be more necessary than pliers, for example, when a nail sticks out of the board almost its entire length. Here you will have to drive the nail “back” first. In this case, it is better to pre-lubricate the cores of large nails with oil, especially if they are rusty. And in order not to dull the edge of the rod too much, a brass or aluminum plate is placed on it.

So, the tip was driven into the wood. Now final extraction nails after pliers.

So you decide to use a suitable size for some purpose old board with nails previously driven into it. However, this is not always feasible. In such cases, if the decorative appearance of the board or the product as a whole does not matter, then it is better to either bend the protruding part of the rod or cut it off with a hacksaw. Sometimes it’s easy to break it off. The protruding head of the nail can simply be driven into the wood with one blow of a hammer.

If the boards have already become unusable, but the nails sticking out in them are still okay, do not throw them away with the boards - they will come in handy.

Don't forget about the old-fashioned method of extraction metal parts made of wood: nails are easiest to obtain using fire. Rejected poles and beams are burned in a furnace or on a fire and, naturally, unburnt nails are selected from the ash.

Large nails are straightened, knocking down scale; small ones are usually no longer good for anything. A nail that has been subjected to fire treatment, even with the scale removed, has an uneven surface, so before driving such a nail, it is again lubricated with oil.

As you know, nails that have undergone fire are less susceptible to rusting. Some craftsmen specially burn new nails, heat them red-hot and immediately after that throw them into cold liquid oil. As a result, the nails acquire hardening and the ability not to rust long time in humid environments.

Massive wooden structures, connected by nails, are first broken with a hammer or sledgehammer. The goal is to create gaps between the parts, into which the blade of an ax, crowbar or nail puller will then be inserted.

The finer the sharpening of the tool, the easier the blade penetrates into the gap and the faster the process of “restructuring” occurs - dividing the structure into separate elements.

Nail extraction technology

To remove nails today you can use a variety of tools, for example:

nail puller,
ticks,
pliers,
hammer with a forked nose, etc.

But despite the fact that there are a large number of tools, in order to pull out a nail, you will need ingenuity and the ability to use one or another tool. For successful work, you need to expose the nail head. In some cases, when the nail is exposed, it can be straightened and knocked out from the back. This can be done using a hammer and another nail.

Using a different nail

Homemade nail puller from a screwdriver

Pliers are a handy tool!

One of the most convenient tools for removing nails is pliers. It is best to have medium to small sized pliers. To reduce the effort needed to remove nails, it is recommended to purchase pliers with a long handle and wide jaws.

Note! If your pliers have small handles, it is not recommended to lengthen them using a tube. This may cause injury!

The nail may bend

Extraction with pincers

Note! To avoid damaging the surface of the workpiece when removing the nail with pliers or other improvised tools, it is wise to use a special backing. If the surface is varnished, then you can place leather or other soft material under the board.

Carpenter's hammer and wire cutters as an alternative to a nail puller!

As for a carpenter's hammer, this item can serve as an excellent tool for removing nails. You just need a hammer that has a forked nose on the other side. When using it without backing, do not pull out a long nail. Therefore, extraction occurs according to the method described above.

Note! This method is effective, however, it carries dangers. If the hammer has a wooden handle, then using it repeatedly as a nail puller can break it. For this reason, it is best to have a hammer with a steel or polyurethane handle on the farm.

With a hammer

How to properly remove a nail from a board?

Removing long nails

Although not in all cases you need to pull the nail out of the board. If it will no longer be used in any way, then the part with the protruding nail can simply be cut off with a hacksaw.

In another case, when the boards are already rotten and the nails are still in good condition, do not rush to throw them away. You can remove the nails using any of the above methods.

Convenient way to remove nails

All / Tool

When driving nails, we very rarely think about the fact that for some reason we will have to pull them out. Meanwhile, such a need still arises periodically. Pulling out nails is a rather labor-intensive process in itself, and if the head of the nail falls off, the task becomes seriously more complicated.

If the nail protrudes slightly above the surface and the head is intact, there will be no particular problem; you only need a nail puller designed specifically for pulling out. However, if there is no cap, there is nothing for the nail puller to catch on, and it turns out to be useless.
The first, fairly simple way to pull out a nail without a head is to use side cutters.

It's simple - How to pull out a nail || STROIM-GRAMOTNO.RU

To avoid damaging the surface, you can place a piece of tin underneath. You can also place a wooden support between the pliers and the part. The main thing is to firmly grasp the nail, which is quite difficult to do without a head. Then, pressing the handles of the pliers and holding the nail tightly, we begin to swing it slowly, from side to side, to gradually pull it out.

Nippers may not be enough if the nail is too deep in the wood or other surface and there is simply nothing to grab onto. In this case, we offer the second option: you can go the opposite way and use a hammer, another nail, a bit, and try to pierce it right through, through the entire board. The main thing in this case is to clearly hit the center of the nail without a head. This method will not help if the nail sticks out in a too thick board or other surface that cannot be penetrated through.

The third way to remove a stuck nail without a head is by heating. Remember from physics course that when heated, bodies expand? And then, as they cool down, they shrink accordingly. You can heat the nail and the surface around it or gas burner, or some thin hot object, by applying it. The metal will expand and contract, the adhesion to the surface will become less strong, and you can still pull out the stubborn nail with the same pliers.
Fourth option: take a piece of pipe whose diameter exceeds the diameter of the nail. One end will have to be jagged, the other will have to be inserted into a drill. Then we simply drill out the nail, installing the jagged tube so that it is in the middle. The nail is quickly removed, but there will be a hole that can be sealed with a plug or putty if necessary.
If you are not afraid of damaging the surface into which the nail is driven without a head, you can try to get to it with a chisel, breaking off pieces of wood around it; in addition, you can also drill a hole nearby with a drill using a regular drill bit.

You can also make grooves on the sides of the nail, form cuts below the broken top, and then pull it out with wire cutters. Minus - the board or other surface will be damaged, and a torn hole will remain in place of the pulled out nail.
As you can see, pulling out a nail is much more difficult than driving it in without a hammer. However, the ingenuity the right tools, and, to be honest, brute force will help you cope with this task.

Apartment renovation involves high-quality finishing walls To prepare a room for wallpapering or applying other decorative covering, walls need to be aligned, having first freed them from the previous fasteners. Often the craftsman has to remove the dowels that have become unnecessary, with which the screws are attached.

Old plank flooring - how to dismantle it correctly?

Dexterity and some tricks can help with this.

You will need

- self-tapping screw;
- corkscrew;
- sharp knife;
- awl;
— nail puller;
- hammer;
- soldering iron;
— punch;
— angle grinder (“grinder”).

Instructions

To dismantle a conventional plastic dowel in the very simple case use a self-tapping screw of the appropriate size. Screw the screw into dowel approximately two-thirds so that the self-tapping screw is securely connected to the part being dismantled. Then hook the head of the screw with pliers and pull it out along with the dowel. In some cases, a table corkscrew can perform the function of a self-tapping screw.

If ordinary pliers do not help, pry the head of the screw into dowel self-tapping screw with a nail puller. This lever allows you to remove dowel with less effort. The main thing is that the screw with its working part fits tightly into the hole.

Homemade wooden dowel remove from the socket in parts. To do this, crush it along the wood grain into several pieces using a chisel with a thin blade and a hammer. Destroyed this way dowel pry with the tip of a sharp knife, a nail or an awl, and then carefully pull out.

If dowel sits securely in the wall, it is not always necessary to pull it out. Such difficult cases sharp knife cut off any protruding surface walls part of the dowel, and cover the resulting depression with construction plaster and level it.

To remove a dowel with a piece of screw stuck in it, use a heated soldering iron. Melt the plastic base of the dowel with a soldering iron, and then pry the piece of fastener with wire cutters or round nose pliers with thin sharp jaws and pull it out of the socket.

Metal dowel in the form of a nail, which are usually hammered into concrete using a construction gun, pre-treat it with frequent strong blows of a hammer. Apply blows to the protruding part of the product from different sides. In many cases dowel It is possible to loosen it in this way, after which it is relatively easily removed with a nail puller.

If metal dowel If you can’t loosen it right away, make indentations in the wall next to it using a drill with a carbide tip or a metal punch. A circular funnel made in this way will reduce the area of adhesion of the dowel to the material walls and makes dismantling easier. If this trick does not help, cut off the protruding part of the dowel with an angle grinder (“grinder”) and level the recess.

Sent by: Sorokina Lydia. 2017-09-15 21:07:23

Learn to pull out nails correctly

When the end of the nail is bent, they straighten it and try to knock the nail out from the back. To make the nail come out of the material more easily when hitting its tip, the protruding part is lubricated with grease, soap, and water. Lubrication is especially necessary when the “tail” of the nail is heavily rusted. Note that when straightened, the “tail” often breaks off. Then, with the toe of a hammer or another nail, you have to act on the end of the “fragment” located in the material in order to lift the head of the latter. (Chisels, hammers, metal rods of suitable size are also suitable for this purpose.)

A special mini-nail puller made from a screwdriver with a forked blade, which is slightly bent in relation to the rod, will greatly facilitate the removal of the smallest nails.

So, we learned how to get to the head of a hammered nail and prepare (raise) it for gripping the nail with a specialized nail tool. Pliers are most convenient for removing clogged nails of small and medium size. The wider the jaws of the pliers (size “K” in the figure) and the longer their handles, the less force will be required to “lift” the wood rod. However, artificially lengthening the handles using metal tubes is unacceptable from a safety point of view, since the usual result of such rationalization is injury.

How to remove a nail from a wall

And in order to reliably hook the rod with the edges of the jaws, significant force is required. It would be nice to continue to pull out the nail and use the head again. This is possible if the supporting surface for the outer roundness of the jaws is increased by placing planks, plates, etc. under the pliers. By the way, a similar technique is used at subsequent stages of pulling out a nail, including using tools of a different design (nail pullers, wire cutters).

By the way, additional wooden or plastic supports placed under the outer roundness of the pliers jaws will perfectly protect the surface of the part itself from damage.

A carpenter's hammer with a forked nose is also useful for removing nails. And here the method of stepwise pulling out nails outlined above is quite acceptable. True, the wooden handle of a hammer is not able to withstand such loads for long and usually soon breaks near the head. If this happens, and there are still a lot of hammered nails left, weld a metal pipe of a suitable diameter to the hammer. Now the claw hammer handle will not break.

Nails are pulled out with pliers only when there are no other tools. Please note that wire cutters are mainly used for stripping wires of insulation and cutting wires made of non-ferrous metals. Therefore, the cutting edges of the wire cutters will certainly become dull, or even chipped, if they are used to clamp steel nails. Moreover, while holding a nail with a diameter of 1-1.5 mm, you cannot squeeze the handles of the pliers too much, so as not to bite the nail.

So, the tip was driven into the wood. Now the final removal of the nail behind the pliers.

So you decided to use for some purpose an old board of suitable size with nails previously hammered into it. However, this is not always feasible. In such cases, if the decorative appearance of the board or the product as a whole does not matter, then it is better to either bend the protruding part of the rod or cut it off with a hacksaw. Sometimes it’s easy to break it off. The protruding head of the nail can simply be driven into the wood with one blow of a hammer.

If the boards have already become unusable, but the nails sticking out in them are still okay, do not throw them away with the boards - they will come in handy.

Don't forget about the old-fashioned method of extracting metal parts from wood: nails are easiest to get using fire. Rejected poles and beams are burned in a furnace or on a fire and, naturally, unburnt nails are selected from the ash.

Massive wooden structures connected with nails are first broken with a hammer or sledgehammer. The goal is to create gaps between the parts, into which the blade of an ax, crowbar or nail puller will then be inserted.

The finer the sharpening of the tool, the easier the blade penetrates into the gap and the faster the process of “restructuring” occurs - dividing the structure into separate elements.

Previous page Up Next page